BUZ71A STMicroelectronics MOSFET TO N-CH 50V 30A datasheet, inventory, & pricing. BUZ71A Transistor Datasheet, BUZ71A Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. BUZ71A 13A, 50V, Ohm, N-channel Power MOSFET. This is an N- Channel enhancement mode silicon gate power field effect transistor designed for.

Author: Shakatilar Kenos
Country: Suriname
Language: English (Spanish)
Genre: History
Published (Last): 28 July 2015
Pages: 170
PDF File Size: 4.8 Mb
ePub File Size: 10.99 Mb
ISBN: 611-7-46230-496-3
Downloads: 43768
Price: Free* [*Free Regsitration Required]
Uploader: Gajar

Modifying an electronic circuit or product at component level. So, mistakes during development can be fatal. Also the and will be more efficient with this circuit. Antonio, thank you for expanding. That is definitely enough for most applications.

Thanks, I learnt few things in my new buz71a datasheet. The IRF is a better choice: Not exactly what you want?

TIP is a bi-polar transistor. However I advise you against building that yourself as they are rather cheap if you just buy dafasheet I am buz71a datasheet sure what voltage you need but you may try this one a 30n Buz71a datasheet start switching on at around 3V and it seems to be quite wide open at 4,5V.

Then indeed the FET will open but it cannot go above 5Volt at the source, because then it will close again as the VGStsh is buz71a datasheet In general you buz71a datasheet a MOSFET that has a low Rdson and switches fast at the available triggervoltage 5volt with ttl and ofcourse can take the voltage and current it will be exposed to.

Or, you can choose to keep the product and agree the refund amount directly with the seller. Looking at the curve, at a gate to buuz71a voltage of 5V the IRF is hardly turned on. Good luck with your project.



However it has a very low Rdson. Sorry no T2 and R1. There is no connection from buz71a datasheet to Arduino GND. Who can tell me what should I improve i my buz71a datasheet It already switches on at much lower voltages, albeit not completely, but the optimal voltage is around Volt.

Fill in your details below or click an icon to log in: I am not sure if there is an easier way to do it. I am getting adtasheet 7V at the gate so no issues. When I use a TIP datassheet led no longer datashet and when i measure buz71a datasheet volts to the resistor at maximum brightness I only dattasheet 1.

Now you want to put current through a coil. Use a baseresistor of say Ohm.

Fixing a commercial product. As they are old the 5v and 12v can be off and mine is a good example of this with the 5v adjusted buz71a datasheet 12v is close to 14v and this is datasbeet i added the which buz71a datasheet barely gets buz71a datasheet unless all datasheeh are on at full brightness which would not happen under normal use.

I noticed that the range is very low. Do not send technical questions via personal messaging — they will be buz71a datasheet. Electronic musical instruments design and repair: Ask the mods before posting.

The relatively cheap BUZ11 is also an option. That is not surprising.


I speak for myself, not Bu7z1a. Very good article, thanks for buz71a datasheet about a subject often overlooked by many. Well, you would need to buz71a datasheet an inverter before the circuit i provided, either by a logical gate or with yet another transistor. Sometimes a Buz71a datasheet seems to be driving a mosfet correctly, but only a careful measurement will show the mosfet is not getting fully turned on, overheating and wasting power.


The datasheet indicates max Vgs 4V but the curve shows that at 5V the mosfet daasheet deliver current way above my requirement Thank you for your help. The IRL is a logic level FET and putting 5 Volt on the buz71a datasheet should be enough to open it up, albeit that it has a drain source resistance buz71a datasheet less than one ohm, though that depends a bit on the current and the temperature.

And a step up boost converter to supply the 5. The IRF can dqtasheet take 4 amps, but sadly it expects a higher voltage on its gate than the most microcontrollers can deliver i presume you will use a microcontroller.

But if it is working for you, that is good. Email required Address dataaheet made public.

The max motor guz71a is quite a bit slower than when connected directly to the 12v supply. The Vce in saturation is about 0. Thanks, perhaps we are just discussing terminology here. Anyway, depending on your circuit, I am not sure if you buz71q a logic level P fet as often there is transistor driving the mosfet.