ATMEGA328 TQFP PDF

The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Shaktinris Mazuzshura
Country: Cayman Islands
Language: English (Spanish)
Genre: Career
Published (Last): 10 December 2006
Pages: 57
PDF File Size: 12.69 Mb
ePub File Size: 6.89 Mb
ISBN: 316-9-68926-220-1
Downloads: 78874
Price: Free* [*Free Regsitration Required]
Uploader: Mezitaxe

That is pretty much all you need. Ground yourself and use an ESD mat. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. If all that is correct, there are a couple other things that could cause that error: Reset is driven by the programmer, and besides has an internal pullup.

Buy Products Online from China Wholesalers at

Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes 0xff 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 no 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no tqgp 0 0 0 0 0x00 0x00 Programmer Type: ATmegaP Chip Erase delay: It looks like the log text says ‘programmer operation not supported’, could be a symptom of bad cmd line args.

  FREEMARK ABBEY WINERY CASE PDF

Have you applied power fqfp the circuit? If you have ever managed to program the fuses, the reset pin may have been disabled, or the device may be expecting an external crystal. This question does not appear to be about electronics design within the scope defined in the help center.

Error while burning bootloader.

ATmegaP Microcontroller – TQFP | ATmegaTQFP | Atmel

If all that is correct, there are a couple other things that could cause that error:. ISP requires a working clock source. Atmega 2 9 I’m voting to close this question as off-topic because it has been abandoned for half a year in unanswerable atmgea328.

TomCarpenter, the programmer does provide power. When programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external atmeha328.

The reset pin lacks the normal ESD protection, and so is fairly easy to fry. Assuming your connection is incorrect, first you need to add a pull-up resistor to the reset pin; 1kk should be atnega328. Clearly I’m doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it.

ATmega328P Microcontroller – TQFP

If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to recover it. It’s worth checking its in the correct position, though. Home Questions Tags Users Unanswered.

  GAUDY NIGHT DOROTHY SAYERS PDF

Only HV programming does not. SCK serial program mode: Check that the ISP header connects to the pins that it ought to, and check that you have the chip oriented correctly in the socket The USBtiny has a switch to power the target, so make sure that’s in the correct position. The AVR programmer will not supply power.

Crystal requirement comes when booting through the bootloader i. Well first of all, check the wiring. Any help would be appreciated.

I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip on right. If this question can be reworded to fit the rules in the help centerplease edit the question.

However, when attempting to upload the bootloader to the chip, I am presented with the following error:. Can you edit the question to include the exact command-line arguments given to avrdude? Using SCK period of 10 usec avrdude: