HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Tygodal Akinogul
Country: Great Britain
Language: English (Spanish)
Genre: Literature
Published (Last): 12 December 2004
Pages: 110
PDF File Size: 9.42 Mb
ePub File Size: 20.1 Mb
ISBN: 653-5-94314-354-9
Downloads: 1422
Price: Free* [*Free Regsitration Required]
Uploader: Doushura

TL — Programmable Reference Voltage. Submitted by admin on 30 October These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. Choosing Encodeg For Robots.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

If you want security you can connect any of the 8 pins to 5V to make it high. This data should be sent to the HT12D encoer decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. The Encoded 12 bit output data can be obtained from this pin.

Supply voltage; 5V 2. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

The IC is has a wide range of operating voltage from 2. The encoded bit can be obtained from the Dout datasehet pin Virgin Galactic — Commercial Space Flight. It is mainly used in interfacing RF and infrared circuits. HT12E has a transmission enable pin which is active low.


The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

These 12 bits are divided into 8 address bits and 4 data bits. They can also be connected encodrr switches to manually send and receive data. What is Web Browser. We should set the bits in same pattern on Encoder and Decoder IC to pair them. This pin has to be connected to Ground 0V to enable the Transmission. The IC has a built in oscillator.

HT12E Datasheet

It is very important that your Decoder should also have this same address for them to talk to each other. Transmission enable; active low. Skip to main content. Simply put, HT12E converts the parallel inputs into serial output. SPI Module of Arduino. This oscillator can be used by connecting these two pins through a 1M Resistor. This cycle is repeated as long as TE is kept low. You can know to set up the HT12D after this from here.

Can range from 2. This high-density System-in-Package SiP integrates controller, power switches, and support components.

Arduino based GPS receiver. Pull the Transmission Enable pin pin 14 to ground to activate transmission. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. HT12E is an encoder integrated circuit of 2 12 series of encoders.


HT12E Encoder IC

The primary function of HT12E is to encode a bit and send it out through the output pin. Interface GPS with Arduino. They are paired with 2 12 series of decoders for use in remote control system applications.

Choosing Battery for Robots. As soon as TE returns to high, the encoder output completes its final cycle and then stops. These two ICs together form an Encoder and Decoder pair.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. In the above circuit I have set the 8-bit datashee data as 0b, ddatasheet connecting all address pins to ground. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Interface SD Card with Arduino. These are the 8-bit address bits, which is used to protect your data. Connected to encpder Ground of circuit. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

Posted In Sex