User Manual () Upgrade Instructions; 07/01/15; Download; Release Notes. Datasheet (). Datasheet () Upgrade Instructions; 08/31/15; Download. Don’t forget about our other Dlink DSLB info that you might be interested in. Login to Dlink DSLB Router · Change your Dlink DSLB IP Address. 5) The power light will first go red and the DSL light will flash. The DSL B comes with a lot of Manual Setup tick box and click the Setup Wizard button.
|Published (Last):||19 September 2015|
|PDF File Size:||4.88 Mb|
|ePub File Size:||18.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
D-LINK DSLB USER MANUAL Pdf Download.
This is the same screen as seen in the Remotelog section under tools. Gently fasten the two slots with the screws. D-Link delivers the performance you need at a price you can afford. The following screen appears after you save your selection. Ensure that the device is properly mounted on the wall with the support of the screws.
You will be able to enjoy the freedom that wireless networking delivers. Note that manula a crossover or straight-through Ethernet cable can be used. Click Exit to close the window. This ensures that time sensitive data e. Page 50 Click Next, and the right page appears.
D-link DSL-2640B User Manual
To save your current configuration, click the Backup Settings button. It is strictly forbidden to use other software for updates. If you uncheck the DSL Auto-connect box, more options will appear below the check box.
The Save button only saves the LAN configuration data, but does not apply the manuaal. When you start the ADSL BER Test, the following progress window will display the connection speed as well as the length of time that the test will run for. The following is a PPPoA example. Page of 95 Go.
In this page, you can configure network traffic classes. This is the percentage of power that should be transmitted from your wireless router.
When finished with your selections, click Next to continue. Advanced Configuration Tick the text boxes of the modulation types you want to enable. Page 66 Enter Remote IP. After proper configuration, click Apply to save the wireless security options and make the modification effect. Virtual Server Internet e. Indicates if MLD is enabled or disabled. Click on the Add button to configure a virtual server. Then decide if you will be using any features such as dial on demand, PPP IP extension, keep alive and then click Next.
At any time during the test, click on the Stop button to terminate the test. Select the desired DSL test mode and then click the Apply button.
D-Link Technical Support
If you wish to enable this protocol, then select enable. Enter the IP address of the management station permitted to access the local configuration and click Apply. For information regarding proper configuration, contact your ISP.
Paste the content of the certificate ddl-2640b you wish to add in the Certificate field and click Apply. Web Configuration After proper configuration, click Next and the right page appears. Table Of Contents Wireless–Advanced These settings are ISP dependant.
The user name or password can only be less than 16 characters.
The virtual channel between two points in an ATM network, ranging from 32 to 1 to 31 are reserved for known protocols Connection mode: Click Apply when finished. Click Add Entries, the following figure appears. Web Configuration Click Add, the right page appears. When you manage the Modem through Web, you must keep the Modem power on.
You need to reboot the DSL router to enable your modification or configuration effective in some cases, mnaual example, after you modify the PVC configuration. Auto Channel Timer min: The beacon interval may be adjusted in milliseconds ms.
Apply Click to save changes. In this page, select a preferred WAN interface as the system default gateway.
Dlink DSL-2640B User Manual
Don’t show me this message again. System Log After enable Automatically synchronize with Internet time servers, the right page appears.
A solid light indicates a connection to an wireless is operational. Page 45 Click Next, and the right page appears. In this page, you can set the service description, enable Page 38 Sdl-2640b Configuration After proper configuration, click Next and the right page appears. Enter proper configurations and click Apply. Leave the remaining fields at their defaults and click Next to continue. You can select the Enter Type from the drop-down list.